Gallien krueger backline 600 price7/16/2023 ![]() Simple and effective, that's what we found on the biggest names in the bass (markbass among others) knob-a boost which is great. Contour filter to dig the mediums = innutile except for the salp and again. Input jack with 3 buttons: active / passive (-10db pad) with an output mute tuner, to agree a silence without removing the plug from the amp and letting the amp on, and a selector cannal A / B (clean / distortion). The diffusion of the sound is even better. It is very convenient in cramped spaces or rehearsal concerts in bars or space is limited. Useful little trick, it can move into position "kickback" = mode its back. 34kg, they must feel when 200m with the amp alone. A conventional handle on the top of the amp and two very well-designed handles on either side of the combo. A large grille protects the well-resistant HP shocks. on the other hand, as there is a hole covered by a grid very solid for this fan, you can not ask for beer on the amp, in case they are reverse = pafff the transition! -Construction is solid, a coating "carpet" covering the entire combo. There is however a small fan on top of security of the amp which gets under way in the event of poor ventilation. ![]() Full transistor amp, it heats well, and all the passive ventilation. So 180W in normal use and if we add another cab, we go a 300W. It's a bit special because no one is not really a combo itself. A mass production coming straight from the U.S. Gallien Kruger Backline presentation of 210. I rachrerais this amp without hsitation, recognizing the need to pair it with a bowl 15 inches. At about 500 in thomman musicstrore or the ratio quality price of GK is for me the best available. For cons, I have a penchant for Ampeg, but when you compare the price, there is no comparison. If we want to harness the power of this amp (to be in 300 w, trs useful in concert) and really make it sound the bass (I play a Warwick Streamer LX 5 strings), it is essential to couple it with a 15-inch dish. I play in a pop / rock group, we have a broad range of compounds: reggae, rock, pop, ballads, etc. There are few examples in the manual of SETTING THE qualisation guiding far departure. I think this amp can be used to find any bass sound that will satisfy. Opportunities as rglages trs large, I have a while before finding one that suits me rglage. Special features of GK: rglage a contour (not bad for the slap) rglage a "boost" (which gives the sound a lot of PCHE) and an overdrive of hell (I have the feel like a guitar when I use it, even if it is for me a gadget plutt). Opportunities are rglages compltes trs: 4 buttons qualisation: treble, high and low mdium, bass. It is equipped for everything you need for scne and studio effects loop, line out (with prpost qualisation), foot switch, tuner. If the couple with a bowl suplmentaire, we get 300w. I *have* seen amps which exploded at turn off, of all times.The backline is an amplifier transistor 210 teams of two bowls 10 inches. PS: check speakers and cables used by your frriend, maybe it had some problem there and a click or pop caused by the ground lifting was the straw that broke the camel´s back.Ī camel which was already quite overloaded. ![]() This amp does not have a proper short circuit protection, but a mute.Īcceptable in a home Hi Fi amp, not enough in the rough stage life. In a nutshell, reproduce, at the Lab, anything your friend can do on stage. (here you might use a resistor instead of a speaker, for sanity).Ĭheck it regularly for undue heating, weird waveforms, something strange. Let it cook for a couple hours at full power. If all looks well, plug it straight into the power line, load it and apply a steady tone to it (400Hz, 1KHz, your choice) raising power step by step until clipping. It might be unstable, on the verge of oscillation. Can't talk about the ground switch, it should damage nothing, but maybe this guy had some weird ground problem and it raised its ugly head when lifting, so in an indirect way it might have somethiong to do.Īnyway: rebuild your amp, test it first with bulb limiter without load, then add a speaker load without turning it off, inject some signal and scope the output.
0 Comments
Leave a Reply. |